SAFE 10YDCO-PRO is a new generation of standalone carbon monoxide detector with breakthrough detection using a second-generation electrochemical sensor and a colour LCD display with environmental functions. Power is supplied by an integrated lithium battery (built in, non-replaceable) guaranteeing exceptionally long operation of the device of more than 10 years and an extended 10-year warranty on both the battery and the device itself. The SAFE 10YDCO-PRO carbon monoxide (CO) detector sets a new level of standard in the fire safety of residential buildings.
Foreword
General
This user manual describes the installation, functions and operation of the SAFE 10YDCO-PRO standalone carbon monoxide detector (hereinafter the “detector” or “device”). The detector works completely independently, with no need to connect to a Hub or mobile app. Read this manual carefully and keep it safe for future reference and for any subsequent user.
Safety instructions
The following signal words may appear in the user manual:
| Signal word | Meaning |
|---|---|
| NEBEZPEČÍ | Indicates a high potential hazard which, if not avoided, may result in death or serious injury. |
| VAROVÁNÍ | Indicates a medium or low potential hazard which, if not avoided, could result in minor or moderate injury. |
| UPOZORNĚNÍ | Indicates a potential risk which could lead to property damage, data loss, reduced performance or an unpredictable result. |
| TIP | Provides methods to help you solve a problem or save time. |
| POZNÁMKA | Provides additional information, such as emphasis or a supplement to the text. |
Revision history
| Version | Revision content | Release date |
|---|---|---|
| V1.0.0 | First release. | September 2026 |
| V1.0.1 | Colours according to the FireSAFE brand (red). | October 2026 |
| V1.0.2 | Technical specifications corrected according to the manufacturer's documents. | October 2026 |
About the manual
- The user manual serves as a reference only. Minor differences may occur between the information provided and the product.
- We are not liable for damage resulting from use of the product in a manner that is not in accordance with the instructions in the user manual.
- The manual will be updated in line with the current laws and regulations of the relevant countries. For detailed information, see the printed user manual or visit our website. The electronic and printed versions may differ in minor details.
- All designs may be changed without prior written notice. As a result of product updates, certain differences may appear between the product and the information in the manual.
- Printing errors or deviations may occur in the description of functions, operations and technical data. In case of doubt or dispute, we reserve the right of final interpretation.
- All trademarks, registered trademarks and company names in the manual are the property of their respective owners.
- If any problems occur while using the device, visit our website, or contact your supplier or customer service.
Operating requirements
- Under no circumstances ignore the detector's alarm – such behaviour could lead to serious injury or death.
- Do not attempt to open or disassemble the detector – there is a risk of electric shock, failure or malfunction of the device.
- Exposing the detector to high or low temperatures or high humidity may considerably shorten the battery life.
- Before using the device, make sure that the detector's power has been activated.
- Use the device in accordance with the instructions given for the operating environment.
- Transport, use and store the device under the humidity and temperature conditions permitted by the manufacturer. Do not expose it to water or moisture, or to dripping or splashing water.
- Do not insert any objects into the ventilation openings, do not cover the product and prevent water or other liquids from entering the detector.
- This CO detector is intended only to indicate the presence of carbon monoxide – it is not intended to detect smoke, flame, temperature or other gases or hazards.
- The device is not intended for use by persons with reduced physical, sensory or mental capabilities or a lack of experience and knowledge, unless they are supervised or have been instructed by a person responsible for their safety.
- Fumes or gases (e.g. from cooking or from the use of cleaning agents, thinners, polishes or paints) may contaminate the detector's sensor and thus affect the reliability of the device in the short or long term.
Installation requirements
- Incorrect installation and operation of this device will prevent it from functioning correctly and consequently from responding to the danger of carbon monoxide.
- Installing this device to monitor CO concentration does not replace the correct installation, use and maintenance of fuel-burning appliances, including adequate ventilation and exhaust, ventilation and extraction systems.
- Before installation, read carefully the chapter Choosing the installation location.
- Do not expose the product to direct sunlight, extreme cold, humidity or sudden changes in temperature.
- Before using and activating the device, you must stick the set of information labels in your language onto it.
- Installation and handling of this device must always comply with local electrical safety requirements, requirements for protection against electric shock and other relevant regulations.
What to do in the event of a CO alarm
If the detector detects a dangerous concentration of carbon monoxide, it sounds a loud alarm signal (85 dB) accompanied by a visual indication from the red LED indicator: every 5 seconds 4 short beeps of the buzzer accompanied simultaneously by 4 flashes of the red LED indicator at regularly repeating intervals, while the blue-backlit display of the detector shows the current measured CO concentration in ppm.
- Stay calm and open all doors and windows. Stop using all fuel-burning appliances and, if possible, make sure they are switched off (e.g. close the emergency valve on gas appliances).
- Press the button TEST/Silence to temporarily silence the alarm (for 9 minutes). If the warning signal persists, inform the other occupants and evacuate the building – leave the doors and windows open and do not return to the premises.
- Obtain medical help for anyone suffering from symptoms of CO poisoning (headache, nausea) and tell the doctor that carbon monoxide inhalation is suspected.
- Call the emergency number 112, the gas supplier on its emergency number, or the appliance service organisation. Make sure the source of the CO leak is identified and eliminated.
If the area is ventilated after the alarm has sounded, the carbon monoxide may disperse before help arrives. Even in that case, it is necessary to identify the source of the CO leak and have its cause eliminated. Do not start using any fuel-burning appliances again until they have been checked and cleaned by a competent person in accordance with national regulations.
Time to alarm as a function of CO concentration
| CO concentration | Time to alarm |
|---|---|
| 30 ppm | 120 min |
| 50 ppm | 60 to 90 min |
| 100 ppm | 10 to 40 min |
| 300 ppm | within 3 min |
About carbon monoxide (CO)
What is carbon monoxide
Carbon monoxide is the main gaseous product of combustion, formed during incomplete (uncontrolled) burning of carbon-based materials. It is a colourless, non-irritating gas with no taste or smell, whose toxic effects impair the blood's ability to carry oxygen. Exposure to a high concentration of CO can lead to serious tissue damage or have fatal consequences. The severity of CO inhalation poisoning depends on the concentration (ppm) and the length of exposure – CO is a cumulative poison, and long-term exposure to low concentrations (>10 ppm) can also cause symptoms.
| CO concentration (ppm) | Effects on adults |
|---|---|
| 100 ppm | Mild headache, nausea, fatigue (flu-like symptoms) |
| 200 ppm | Dizziness and headache within 2–3 hours |
| 300 ppm | Nausea, headaches in the temples and forehead, drowsiness, disorientation and rapid heartbeat; life-threatening after more than 3 hours of exposure |
| 400 ppm | Severe headaches, convulsions, failure of vital organs; death may occur within 2–3 hours |
- This device may not prevent the effects of continuous exposure to carbon monoxide and will not fully protect individuals with specific medical conditions.
- The device detects only carbon monoxide (CO); it does not detect other gases, smoke or flame. If there is any doubt about the cause of the signalling, a dangerous CO level is assumed and the occupants should be evacuated.
Possible sources of carbon monoxide
CO is produced by the incomplete combustion of carbon-based fuels (coal, wood, charcoal, heating oil, paraffin, petrol, propane, butane, natural gas).
- Fuel-burning appliances – gas boilers, heaters, cookers, wood, solid-fuel or pellet stoves, fireplaces, charcoal barbecues, especially when poorly maintained or inadequately ventilated.
- Equipment with internal combustion engines – portable generators, cars, lawnmowers – pose a deadly danger in enclosed spaces (garages, utility rooms).
- Portable gas heaters, warmers or barbecues (gas and charcoal) used indoors.
- Blocked or obstructed flue gas routes, flues and chimneys.
- Other sources: large amounts of tobacco smoke, town gas, emissions from a smoking fireplace or emissions from neighbouring flats in multi-occupancy buildings through shared or poorly positioned flues.
Basic steps to protect against CO poisoning
- Install one or more carbon monoxide detectors in your home (see Choosing the installation location).
- Have a qualified technician inspect your heating system and fuel-burning appliances (boilers, gas, oil and other similar appliances) every year.
- Have a qualified technician inspect and professionally clean your flue gas routes (flues, chimneys) every year.
- Make sure that fuel-burning appliances and engines are used only in very well-ventilated spaces.
- Use gas appliances according to the manufacturer's recommendations. Never use a gas cooker or oven to heat a room.
- Do not use barbecues indoors or in an adjoining garage.
Functional elements
- Buzzer – provides acoustic information (85 dB) on the states of the device's individual modes, accompanied by visual signalling from the LED indicator.
- LCD display – multifunction, shows the current CO concentration (ppm), temperature and humidity, or the highest measured value.
- LED indicator – provides visual information via a three-colour LED indicator (red = alarm, green = power, yellow = fault).
- TEST/Silence button – verifies the functionality of the device and is used to temporarily silence the acoustic alarm signal, recall the memory of the highest measured values and reset.
- Battery location – built-in battery, not user-replaceable.
- Blocking clip – removing it activates the device's built-in battery.
- Deactivation port – port for inserting the deactivation pin.
- Deactivation pin – for permanent deactivation of the built-in battery (before the device is disposed of).
Principle of operation
The detector is designed for continuous monitoring, detection and signalling of the presence of carbon monoxide (CO) in residential areas. To detect CO it uses advanced second-generation electrochemical sensor technology with high sensitivity and stable performance, capable of detecting even very low concentrations of CO (from 30 ppm). Throughout its service life (more than 10 years) the sensor requires no further calibration. The detector is controlled by an AI SAFE microprocessor and signals danger both visually and acoustically.
Device Type B is intended for both fixed and portable installations and is certified in accordance with the European standards EN 50291-1:2018 and EN 50291-1:2018/AC:2021 for carbon monoxide detectors.
LCD display description
The backlit multifunction LCD display shows information depending on the current ambient conditions:
- With no CO present – alternately shows the current temperature (accurate to ±0.1 °C) and humidity (accurate to ±1.5 % RH), approximately every 5 seconds.
- When CO is present – alternately shows the current CO concentration, temperature and humidity (approximately every 5 seconds).
- In alarm mode – the display's blue backlight comes on and the current CO concentration is shown in ppm.
Temporary alarm silencing
If the detector detects the threshold CO concentration level, it triggers the warning signal. In the event of a false alarm, the acoustic signal can be temporarily silenced by pressing the button TEST/Silence for 9 minutes (this can be activated only when the CO concentration is below 300 ppm). Temporary silence mode is indicated by the red LED indicator (alarm), which flashes 4 times every 5 seconds without an accompanying buzzer sound. If the CO concentration subsequently falls below the specified value, the detector automatically returns to normal operating mode.
Highest-reading memory
The detector has a highest-reading memory function. Pressing and holding the TEST/Silence button recalls on the LCD display the highest measured values since the last memory reset. To manually reset the device and the memory, press and hold the TEST/Silence button in test mode.
Signalling
| Mode | LED indicator | Buzzer / display |
|---|---|---|
| Activation | No signalling | No signalling; the LCD backlight comes on for 3 s |
| Standby mode | Green LED (POWER) 1× every 60 s | No signalling; the display alternately shows temperature and humidity |
| Alarm mode | Red LED (alarm) 4 flashes every 5 s | 4 short beeps of the buzzer every 5 s; the display shows the CO concentration in ppm |
| Test mode | 6 flashes (green, yellow, red, 2×), pause, repeat | 4 short beeps, pause, 4 short beeps, ending with 1 beep |
| Highest-reading mode | Green LED (POWER) 4 flashes every 5 s | Short beep every 3 s |
| Temporary silence | Red LED (alarm) 4 flashes every 5 s | No signalling |
| Low battery voltage | Yellow LED (FAULT) 1 flash every 60 s | 1 short beep every 60 s, for 30 days |
| Fault | Yellow LED (FAULT) 2 flashes every 60 s | 1 short beep every 60 s |
| End-of-life signalling | Yellow LED (FAULT) 3 flashes every 60 s | 3 short beeps every 60 s, for 30 days |
Choosing the installation location
CO detectors should ideally be installed in all rooms containing a fuel-burning appliance. We strongly recommend installing additional detectors in bedrooms and in rooms where you spend a lot of time during the day – in places where you will hear the signal even when asleep (e.g. on the bedside table in a bedroom).
Which rooms to install in
Install a detector in every room containing a fuel-burning appliance as a priority. Install further devices so that the signal is audible to occupants of remote rooms (living rooms, all bedrooms) as well. If there are several appliances and the number of detectors is limited, consider:
- placing one in the room with appliances without a flue or with an open exhaust,
- placing one in the room where users spend the most time,
- in a living bedroom, placing it as far from the cooker as possible but as close as possible to where people sleep,
- if the appliance is in an unused room (e.g. a boiler room), positioning the detector so that the signal is better audible,
- if the appliance has an extended or concealed flue, installing a detector in every room through which the flue passes.
Where in the room to install
A room with a fuel-burning appliance (stove, boiler, gas fireplace, fireplace): CO rises with the warm mixture of gases, so install the detector above the level of the appliance and close to the ceiling:
- the top edge of the detector at least 15 cm from the ceiling, the bottom edge at most 30 cm from the ceiling,
- above the level of the top edges of windows and doors,
- at a distance of at least 1 m and at most 3 m (horizontally) from the edge of the nearest potential source of CO,
- if there are partitions in the room, on the same side as the potential source of CO,
- in a room with a sloping ceiling, on the higher side of the room.
Bedrooms or rooms remote from the appliance (corridors, landings): install the detector on the wall at a height of 1,5–1,6 m above the floor, near the users' breathing zone. Never install the detector at floor level – carbon monoxide is lighter than air and only rarely settles near the floor.
Where not to install the detector
- In an enclosed space (e.g. in a sideboard or behind a curtain) or near a door or window.
- Directly above a sink, in a garage with vehicles starting up, near heat sources or air-conditioning vents.
- In close proximity to a cooker, hobs or deep fat fryers – there is a risk of sensor contamination.
- At or near floor level.
- In places exposed to direct sunlight, extreme cold, moisture or sudden changes in temperature.
- In areas of extreme humidity (>95 %) – bathrooms, showers; or directly above a sink or near dishwashers and washing machines.
- Where there is a risk of contamination by insects, dust or dirt.
- Where it may be built in or covered (curtains, furniture) or detection may otherwise be restricted.
- Near a cooker hood, ventilation openings or places with strong air flow.
- In rooms where the temperature can drop below −10 °C or rise above 55 °C (garage, unfinished loft).
- In areas with restricted or dangerous access – the device must be tested and maintained regularly.
Installing the detector
The SAFE 10YDCO-PRO detector can be installed in two ways – fixed wall mounting, or free-standing on a horizontal surface thanks to the two stabilising feet on the base of the device.
Wall mounting
- Following the chapter Choosing the installation location select a suitable location.
- Using the supplied drilling template, drill holes (⌀ 5 mm) at the installation location and insert wall plugs into them.
- Insert self-tapping screws into the wall plugs and tighten them so that a gap of approx. 5 mm remains between the screw head and the wall.
- From the set of information labels, stick labels A and B onto the front of the device and label C onto the back, all in the required language.
- Activate the CO detector by pulling out the blocking clip on the back of the device. Keep the blocking clip – it can be reused to temporarily interrupt the power, for example when moving house, to prevent the alarm from being triggered accidentally.
- Place the CO detector, back first, onto the heads of the self-tapping screws and slide it downwards so that the screw heads engage in the locking position of the openings in the detector.
- After installation, test the functionality of the device by pressing the TEST/Silence button – check that the LED indicators, buzzer and LCD display are working correctly (see Function test and Silence).
Free-standing installation on a horizontal surface
The design of the detector base has two stylish feet that allow flexible and stable free-standing installation on a horizontal surface.
- For free-standing installation, the detector must be placed in an upright position – it must not be laid flat on a horizontal surface.
- Place it so that there is no risk of it being knocked over, falling or being otherwise damaged.
- Even for free-standing installation, observe the recommended placement described in the chapter Choosing the installation location.
Function test and Silence
After installing the device, or during its regular maintenance, a CO detector test must be carried out to prove its functionality.
- Briefly press the button TEST/Silence – the blue backlight of the LCD display comes on for 5 seconds.
- While the display is backlit, press the TEST/Silence button again – the device activates test mode.
- The display alternately shows information icons together with the current CO concentration, the last highest measured value, temperature and humidity; the buzzer sounds 4 short beeps accompanied by 6 flashes of the LED indicator (green, yellow, red, 2×), pause, repeat, ending with 1 beep of the buzzer and a flash of the red LED.
In the event of a false alarm or if necessary, the acoustic signal can be temporarily silenced by pressing the button TEST/Silence for 9 minutes (this function can be activated only when the CO concentration is below 300 ppm). If the CO concentration subsequently falls below the specified value, the detector automatically returns to normal operating mode; otherwise, after the silence time has elapsed, it returns to alarm mode.
If the device test is not completed successfully, send it in for a warranty claim.
Maintenance
- The CO detector should be cleaned at least once a month. Use a vacuum cleaner to remove accumulated dust particles through the openings around the perimeter of the detector. Wipe the outside of the detector with a damp cloth. After cleaning, test the device with the TEST/Silence button. Avoid cleaning the detector with cleaning solutions or solvents to prevent possible sensor contamination and loss of warranty.
- Do not use substances near the detector that may affect the reliability and sensitivity of the sensor in the short or long term or cause a false alarm: methane, propane, isobutene, isopropanol, ethylene, benzene, toluene, ethyl acetate, hydrogen sulphide, hydrogen, sulphur dioxide, alcohol-based products, paints, thinners, solvents, adhesives, hairsprays, aftershaves, perfumes and some cleaning products.
- A high concentration of tobacco smoke can trigger the alarm warning signal. The detector may also react to short-term exhaust gas leaks, for example when an appliance is first started, or to hydrogen produced when some batteries are charged or when concrete or filler is drying.
- Do not paint the device – paint may seal the air circulation openings and impair the sensor's ability to detect carbon monoxide.
- Do not place the device in places prone to vibration and shocks, or near sources of open flame.
- Do not install the detector in places where sufficient air flow is not ensured, near fans or other devices connected with air conditioning.
- Do not disassemble the detector or interfere with its internal electrical circuits – any such interference leads to loss of the warranty. Servicing is carried out only by the manufacturer's authorised service centre.
End of life
The battery of the SAFE 10YDCO-PRO detector is built in and not user-replaceable. The detector must be replaced with a new one after 10 years from the date of installation – the replacement date is shown on the information label on the back of the device. The detector signals that its end of life is approaching by flashing the yellow LED indicator (FAULT) 3 times, accompanied by 3 beeps of the buzzer, at regular 60-second intervals for 30 days.
- Tear off information label C on the back of the device and use a flat screwdriver to remove the deactivation pin.
- Insert the pin into the deactivation port, push and turn it. If the LCD display stops showing any information, the built-in battery has been deactivated successfully.
Technical specifications
| Detection parameters | |
| Detected gas | Carbon monoxide (CO) |
| Sensor | Electrochemical CO sensor, 2nd generation |
| Microprocessor | AI SAFE with predictive algorithm |
| Device type | B (fixed and portable installation) |
| Calibration | Not required during the service life of the sensor |
| Temperature measurement accuracy | ±0,1 °C |
| Humidity measurement accuracy | ±1.5 % RH |
| Signalling | |
| Acoustic | ≥ 85 dB at a distance of 3 m |
| Visual | Three-colour LED indicator (green = power, yellow = fault, red = alarm) + backlit LCD display |
| Silence function | Yes – TEST/Silence button |
| Silence time | 9 min |
| Highest-reading memory | Yes |
| General | |
| Order code | SAFE 10YDCO-PRO |
| EAN code | 0703123018210 |
| Power supply | 3 V DC, 1× CR17450A lithium battery (integrated, non-replaceable) |
| Current consumption | Standby mode ≤ 20 µA; in alarm ≤ 20 mA |
| Battery / device life | 10 years |
| Operating temperature | −10 °C to +55 °C |
| Operating humidity | up to 95 % RH (non-condensing) |
| Storage temperature / humidity | −20 °C to +60 °C, 5–95 % RH (non-condensing) |
| Dimensions | 133.5 × 63.5 × 28.9 mm |
| Weight | 122 g (with battery) |
| Package dimensions / weight | 45 × 80 × 135 mm, 193 g |
| Carton | 540 × 430 × 335 mm, 96 pcs, 20.1 kg |
| Mounting method | On a wall, or free-standing on a horizontal surface |
| Type of installation | Indoor |
| Degree of protection | IP30 |
| Certification | EN 50291-1:2018; EN 50291-1:2018/AC:2021; BS EN 50291-1:2018; certificate No. R 50607144 0001 |
| Warranty | 10 years (on the device and battery) |
Package contents
- CO detector – 1 pc
- Drilling template – 1 pc
- Self-tapping screws – 2 pcs
- Wall plugs – 2 pcs
- User manual with a set of information labels – 1 pc
Safety notices
- Read these instructions carefully before use and keep them for future reference and for any subsequent user.
- Under no circumstances ignore the detector's alarm – such behaviour could lead to serious injury or death.
- Do not attempt to open or disassemble the detector – there is a risk of electric shock, failure or malfunction of the device.
- Exposing the detector to high or low temperatures or high humidity may considerably shorten the battery life.
- Transport, use and store the device only under the humidity and temperature conditions permitted by the manufacturer. Do not expose it to water, moisture, or dripping or splashing water.
- Do not insert any objects into the ventilation openings, do not cover the device and prevent water or other liquids from entering.
- The detector serves only to indicate the presence of carbon monoxide – it does not detect smoke, flame, temperature or other gases or hazards.
- The device is not intended for use by persons with reduced physical, sensory or mental capabilities, or by persons lacking sufficient experience and knowledge, unless they are supervised or have been instructed by a person responsible for their safety. Children must be supervised to ensure that they do not play with the device.
- This device must be installed by a competent person in accordance with the manufacturer's instructions; installation does not replace the correct installation, use and maintenance of fuel-burning appliances, including adequate ventilation.
- Do not attempt to remove or replace the battery inside the detector. When its life has expired, replace the whole detector with a new one (see End of life).
- Do not dispose of the product with general municipal waste or burn it – hand it in for recycling in the electrical equipment take-back system.
Warranty
The manufacturer provides a warranty on the SAFE 10YDCO-PRO detector 10 years from the date of sale, covering both the device and the integrated battery. Under the warranty, the manufacturer's obligation is limited to repairing or replacing the detector, or any part of it, in which a defect in material or workmanship is found.
The warranty becomes void if the product has been damaged, altered, misused or modified after purchase, or if it has stopped working as a result of poor maintenance or incorrect placement. The warranty does not affect your statutory rights.
In case of problems with the device, first contact technical support – most situations can be resolved remotely.
Need help?
SAFE HOME europe technical support:
E-mail: info@safe-home.eu · Telephone: (+420) 581 222 262
Web: www.smart-safe.eu